ENSONIQ ASR-10 Spécifications Page 137
- Page / 154
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
I
SP-3 SCSI Interface Manual
I
SCSI Troubleshooting
Error Messages (in alphabetical order)
r
Message:
DISK DRIVE fiCT RERDY
DISK HRS BEEI‘ CHRffGED
DRIVE ffOT RESPIJfYDlMG
IMURLID
LORD
DEVICE
IYCT Rrl RSR SCSI
DEV
UMCOtifiECTED SCSI
DEW
Defined:
This message usually occurs
when the ASR-10 is trying to
access the floppy drive or a
removable SCSI Storage
Device when there is no disk or
cartridge in the drive.
The disk (or cartridge) has
been ejected from the drive
since the last time the drive
was accessed bv the ASR-10.
If encountered while using a
SCSI Storage Device, this error
may indicate a problem with
your SCSI cables. The cable
from the ASR-10 to the Storage
Device may be too long, or the
system may not have proper
termination.
No SCSI device with this ID
was connected to the network
when the ASR-10 booted UD.
The SCSI device selected is
not an ASR-10 formatted
storage device, and cannot be
used by the ASR-10.
A SCSI device that was
detected by the ASR-10 at
bootup is no longer connected
or turned on.
Final Thoughts
What to Do:
If this message occurs, insert a floppy disk or
cartridge in the drive, then use the CHANGE
STORAGE DEVICE Command to select the
a ro riate SCSI ID number (or press
B
LOAD , then (INSTRUMENTJ. This event may
take place because of improperly saved files.
Refer to the section on “Transferring Banks
pe;c;.floppy Disk to a SCSI Storage
Reinsert the disk or cartridge, press (LOAD),
then (INSTRUMENT), and continue.
Check all connections and make sure that you
are using the correct cables. Make sure you
have the proper termination. If this message
appears repeatedly while files are being saved
to the disk, then it is likely that you are
invisibly losing sectors of your disk. Correct
the problem before continuing to use the disk.
Use the CHANGE STORAGE DEVICE
Command to verify that you are using the
correct SCSI Device number.
You may choose to reformat the SCSI
Storage Device for use with the ASR-10. Use
caution, as this will erase all previously saved
data on the SCSI Storaae Device.
Check your SCSI connections. If your SCSI
Storage Device has a changeable ID number,
make sure it matches the SCSI Device
Number you have chosen in the CHANGE
STORAGE DEVICE Command.
The main problems that you are likely to encounter are the SCSI Storage Device problems
described above and cable problems. These are some additional recommendations to help
eliminate many problems:
1.
Use the shortest cable possible when connecting SCSI Storage Devices.
2 Be sure to use proper termination. Refer to the SCSI Terminators section of this manual.
3.
If you need to use an extension cable between your ASR-10 and your SCSI storage device(s),
use high quality shielded SCSI extension cables only (do not use printer cables).
4.
Avoid running SCSI cables across power cables and other sources of powerful
electromagnetic fields.
5.
It is required that the SCSI Storage Device supply power to the SCSI bus. Check your SCSI
Storage Device manual for further information.
6.
Some SCSI Storage Devices may have their SCSI Device ID number set internally. Refer to
the SCSI Storage Device’s manual or manufacturer for more information.
7.
If you use an Apple computer in your setup, be sure to use a short (18” or shorter) Apple-
brand SCSI cable between the computer and the first connected SCSI Storage Device.
Remember, most of the problems we encounter are with cabling or with systems that are not
terminated properly. If you encounter a problem, make sure you have checked these things
carefully before assuming that your ASR-10,
SF’-3
or your SCSI Storage Device are at fault.
ENSONIQ ASR-10 Version 3 Operating System
127
- ENSONi’a]‘” 1
- READ THIS FIRST! 2
- Advanced Sampling Recorder 3
- Version 3 Operation System 3
- Table of Contents 5
- Troubleshooting 8
- List of Tips 10
- What’s New in 3.0 11
- What’s New in 2.5 11
- What’s New in 2.0 11
- What’s New in 1.5 12
- Backing Up the O.S. Disk 13
- Introduction 14
- New Command/Instrument Pages 15
- How To Import Akai Samples 16
- LOAD DEVICE 16
- F'RRTITI2r"l=X 16
- PARTITION 16
- RANGE LO HI Ranges: 17
- NEW NAME 18
- RM2THER? 18
- (ENTER-YES] 19
- DEVItE=XXXXXX 20
- RANGE LO HI 21
- II”)PORTII”IG 21
- Memory Limitations 23
- Layer Limitations 24
- Final Suggestions 25
- New System*MIDI Parameters 27
- ENTER-YES). YOU 28
- ENTER-YES) button. You have 28
- ENTER-YES]. The WaveSample 28
- NTER-YES) repeatedly, and 28
- BRCKUPIREST08E 29
- Please Note the Following! 30
- Caution!Caution! 30
- Sample DAT 31
- What You Need To Get Started 32
- SCSI Review 33
- DAT BACKUP 34
- Select the DAT BACKUP Command 35
- Go Ahead 35
- RECORD-ENTER 37
- COflPLETE 37
- SYSTEM STOP 38
- VERIFY,----OF 38
- DAT RESTORE 39
- DAT VERIFY 40
- User Retry 41
- COMMAND) 42
- Audio Track Recording 43
- Give It a Try! 43
- An Audio Track Tutorial 43
- Play Along with the Sequence 44
- Record Your First RAMTrack 45
- Press Play and Enjoy! 45
- Master Directly to DAT 45
- Save your Work 45
- Caution: 46
- GI’SK-HIT EMTER 47
- Infernal RAM Memory 48
- Types of Audio Tracks 49
- Song Audio Tracks 50
- All About Memory 51
- DiskTrack 53
- recording: 53
- Auditioning DiskTracks 56
- PLRYIREC=OFF 57
- 1 or 2 Inputs? 58
- INPUT+FX Signal Chain Routing 60
- MAIN-OUT Signal Chain Routing 61
- ENTER-YES) (when the 62
- Audio Tracks in “Chain Play” 63
- Which Track is Selected? 64
- Tie the Jack to the Track 64
- Overdubbing 65
- Amalgamation 66
- Audio Triaaer event: 69
- Bounce-Down 71
- Bounce-Down 72
- 240-2 Bounce-Down 72
- Notes on Bounce-down: 72
- Song Audio Track 73
- Audio Track Storage 74
- .&ution: 75
- BRNK MRIIE=RJRK JUT 76
- DELETE EL 76
- L’ERSIEN? 76
- Deleting: 79
- To Delete a RAM AudioSample: 79
- Delete a SCSI AudioSample: 79
- SRL’E GL3BRL 81
- PRRRflETERS 81
- 72 ENSONIQ 82
- New Sequencer Parameters 83
- COMMAND) will leave them 86
- New (Audio) Track Parameters 87
- RSf:PLNFI17E=RS::PL--u”CO3U 88
- RflE=‘U1‘1CEFI1”1ED* 88
- AUDIO TRACK) button) 91
- Caution:Caution: 92
- System Optimization Tips 95
- AudioSample Specs 95
- INSTRUMENT), and 97
- ENTER-YES to begin 97
- ENTER-YES), or selecting an 99
- ENTER-YES) 100
- Effect Parameters 102
- Additional Effect Parameters 116
- SP-3 SCSI Interface Manual 117
- Getting Started 118
- SCSI Terminators 119
- ~.WZllTliilg: 121
- Selecting the Storage Device 123
- ENTER-YES) 125
- Managing Disk Files 127
- Directories 128
- Directory Commands 129
- Directory Recommendations 130
- I I I I 1 130
- File Paths 131
- Bank Files 131
- Direct-MacrosTM 132
- TRACK) locations contain 135
- INSTRUMENT), and continue 137
- Limited Warranty for the SP-3 138
- What is the DI-10 Digital 139
- Interface? 139
- About the Digital Input 139
- Easy All-Digital Sampling 140
- Starting to Record 141
- Normalizing Gain 142
- Default Output Routings 142
- About the Digital Output 142
- DI-10 Appendix 143
- DI-10 Digital 144
- Glossary 145
- Version 3 Index 147
- DEFINITION 101 148
- MAIN-OUT48,61 150
- SAVE THESE INSTRUCTIONS 153
- EN50NiPI”’ 154
Produits connexes et manuels pour Pianos numériques ENSONIQ ASR-10
(9 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.744 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels